This great article listed below involving Tools You Need to Install a New Bathtub is exceptionally captivating. Check it out for your own benefit and decide what you think about it.
Installing a bathtub isn't specifically rocket science, but it does require strong plumbing, woodworking, as well as often, tiling skills. Changing an old bath tub with a brand-new one is likewise a moderately hard job. If the old tub is conveniently obtainable, the job can move easily; if you need to open a wall surface to remove the old bathtub and position the new tub, the job is much harder. In either situation, the project is within a residence handyman's abilities, although you will certainly need an assistant to leave the old tub and also set in the brand-new one. Make sure you have certified yourself for the task and also are comfortable attempting it. As opposed to hiring a service provider to take control of a halfway-completed task, it is better to think about utilizing one prior to you start. Opportunities are you might need a professional plumber to make tube links.
This post will certainly aid you set up a brand-new tub in your restroom if you have already bought a new bathtub and don't need to alter the arrangement of your previous water pipes.
Your tools and material list ought to make up the following:
Removing Old Touches
If you require to change old faucets with new ones as a part of your setup, after that the first thing you should do is detach the water system. After doing so, activate the faucets to drain any kind of water continuing to be in the system. The procedure of eliminating the existing taps can be quite troublesome due to the restricted accessibility that is commonly the instance.
Use a container wrench (crowsfoot spanner) or a faucet tool to undo the nut that connects the supply pipes to the faucets. Have a fabric all set for the continuing to be water that will certainly come from the pipes. When the supply pipes have been eliminated, utilize the exact same tool to loosen up the nut that holds the taps onto the bath/basin. You will need to quit the solitary faucets from turning during this process. Once the taps have actually been eliminated, the holes in the bath/basin will have to be cleansed of any kind of old securing substance.
Before moving on to fit the new faucets, compare the pipe links on the old faucets to the new taps. If the old faucets are longer than the new taps, after that a shank adapter is needed for the brand-new taps to fit.
Fitting New Taps
If the tails of the brand-new faucets are plastic, then you will certainly need a plastic adapter to prevent damage to the string. One end of the connector fits on the plastic tail of the faucet and the various other end provides a link to the existent supply pipes.
If you need to fit a monobloc, then you will certainly require lowering couplers, which connects the 10mm pipe of the monobloc to the standard 15mm supply pipe.
Next, place the faucet in the placing opening in the bath/basin guaranteeing that the washing machines are in place between the tap as well as the sink. Protect the tap in place with the producer supplied backnut. When the faucet is firmly in position, the supply pipelines can be linked to the tails of the faucets. The taps can either be connected by utilizing corrugated copper piping or with regular faucet adapters. The previous type ought to be connected to the tap ends initially, tightening only by hand. The supply pipes can later on be linked to the other end. Tighten up both ends with a spanner after both ends have been linked.
Setting up the Bath tub
Utilizing the two wood boards under its feet, place the bathtub in the required placement. The wooden boards are valuable in uniformly spreading the weight of the bathtub over the location of the boards rather than focusing all the weight onto four tiny factors.
The following objective is to make sure that the bathtub is leveled all round. This can be accomplished by checking the spirit level and also changing the feet on the bath tub till the spirit level checks out degree.
To mount faucets, fit all-time low of the furthest flexible tap adapter to the appropriate supply pipe by making a compression join; then do the exact same for the other tap.
Turn on the water system as well as examine all joints and also brand-new pipework for leakages as well as tighten them if needed. Fill up the tub and also examine the overflow outlet and also the regular electrical outlet for leaks.
Finally, deal with the bathroom paneling as explained in the manufacturer's instruction manual. Tiling and securing around the bathtub needs to wait up until the bathtub has actually been used a minimum of once as this will resolve it right into its last setting.
Planning for the Installment
To start with, the sustaining framework supplied with the bath ought to be fitted (if required) according to the producer's instructions. Next off, fit the faucets or mixer to the bathtub. When fitting the tap block, it is essential to make sure that if the tap features a plastic washer, it is fitted in between the bath as well as the taps. On a plastic bathroom, it is likewise reasonable to fit a sustaining plate under the taps unit to avoid stress on the bathtub.
Fit the adaptable tap adapters to the bottom of the two faucets utilizing 2 nuts and also olives (in some cases provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the electrical outlet through the hole in the bath. Use the nut supplied by the supplier to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the versatile overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which need to be fitted inside the bath. Make sure you make use of every one of the supplied washing machines.
Link the trap to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Attach the bottom of the overflow tube in a comparable manner.The bath need to now prepare to be fitted in its last position.
Tiling Around the Bath tub
In the area where the bath fulfills the tile, it is needed to seal the joins with a silicone rubber caulking. This is necessary as the installation can move enough to split a rigid seal, causing the water to pass through the wall surface between the bath as well as the tiling, causing complications with dampness and possible leakages to the ceiling listed below.
You can pick from a selection of coloured sealants to blend in your components and also installations. They are sold in tubes and cartridges, and also can sealing voids as much as a width of 3mm (1/8 inch). If you have a bigger space to load, you can load it with spins of soaked paper or soft rope. Remember to constantly fill up the bath tub with water before securing, to allow for the movement experienced when the bathtub remains in use. The sealer can crack relatively very early if you do not take into consideration this movement before securing.
Additionally, ceramic coving or quadrant floor tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are additionally quickly offered on the marketplace. It is recommended to fit the tiles utilizing waterproof or water resistant glue and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I hope you liked our article about Tools You Need to Install a New Bathtub . Thank you for spending some time to read through our article. Sharing is caring. Helping people is fun. We treasure reading our article about Tools You Need to Install a New Bathtub .
Efficient help? Call!